Transmitters PLUG-IN DC Input JH4300 (Voltage & Current)
Monday, 06 June 2011 03:44 Last Updated on Monday, 29 August 2011 00:10 Written by Administrator

DC INPUT TRANSMITTER
PLUG-IN MODULE, FIXED RANGE

 


JH4300: DC Voltage or Current Inputs, Input/Output Isolated
    • Input Ranges from 4mV to 250Volts, 1mA to 5 Amps
    • Quick-Check Red/Green Output LEDs
    • Industry Standard Pinouts (8-Pin Socket)
    • Nonstandard Ranges Available
    • AC or DC Power Options

    JH4300
    PDF
    DATA SHEET

    JH4300
    PDF
    MANUAL

Model JH4300 provides a DC output proportional to a DC voltage or current input. A fixed-range device, it is precisely calibrated to your specified range at the factory. (For a rangeable device see JH4380W Fully Rangeable Transmitter.)

Red-green Quick-Check LEDs give a quick indication of the relative output. Red is brighter at the low end, green at high, while at mid-scale both are approximately equal. Red-only indicates offscale low while green-only indicates offscale high.

A low-drift input amplifier is included for millivolt-level inputs. This feature was formerly an extra-cost option designated by Model Number JH4310. Available options include AC or DC power choices and reverse-action Option RT (decreasing output with increasing input).

ORDERING INFORMATION

Model Number:   Select JH4300-AC for AC power, JH4300-DC for DC power.
Input Range: Specify any DC voltage or current range allowed by the "Input Capabilities" spec, below.
Output Range:   Specify any DC voltage or current range allowed by the "Output Capabilities" spec, below.
Power: Specify 115Vac, 230Vac, 12Vdc, or 24Vdc.
Reverse-Acting Transmitter:   Decreasing output with increasing input.  Specify option RT.
Loop-Powered Output: 4/20 mA "current sink" output stage for connection to devices whose inputs provide 24 Vdc loop excitation.  Specify Option LPO.
Urethane Coating:  

Specify Option U

INSTALLATION AND CONNECTIONS

The JH4300 plugs into any standard 8-pin circular ("octal") relay socket. JH Technology offers a socket suitable for DIN-rail or surface mounting   (see the Accessories page). Pin connections are:

Pin 1: Power (AC or, if DC power option, DC plus).
Pin 2: No connection.
Pin 3: Power (AC or, if DC power option, DC minus).
Pin 4: No connection.
Pin 5: Input plus.
Pin 6: Input minus.
Pin 7: Output plus.
Pin 8: Output minus.

DETAILED SPECIFICATIONS

Voltage Input Capabilities: 4mV minimum span, +/-250V maximum input. Offset ranges are allowed.

(Input Impedance: 200kohms or greater.)  
Current Input Capabilities:  1mA minimum span, +/-5 Amps maximum input. Offset ranges are allowed.

(Input Resistance: Varies with input range. Contact factory for details. 62 ohms for 4/20mA input.)
Voltage Output Capabilities:    1 volt minimum output span, -10 to +15V absolute limit. Offset ranges are allowed. Maximum output load, 10mA (1Kohm at 10V output).
Current Output Capabilities: 

1mA minimum output span, 0 to +25mA absolute limit. Positive offsets are allowed, negative outputs are not. Output drive capability, 24V (1,200 ohms max. at 20mA output).
Accuracy (factory calibration): 

+/-0.1% of span or 10 microvolts, whichever is greater.
Adjustability: 

Zero and span each are adjustable approx. +/-15% of span.
Linearity: 

+/-0.05% of span or better.
Response Time: 

Under 100 milliseconds.
Isolation: 

Power, 1,500Vac rms (2,100V peak). Input/Output 1,000Vac rms (1,400V peak).
Guaranteed Operating Temperature: 

-10 to +60 deg. C (14 to 140 deg. F).
Temperature Stability: 

+/-(0.02% of span plus 1.3 microvolts) per deg. C, or better.
Power Requirements: 

AC, 115 or 230Vrms, 50/60Hz, 2.5V-A. DC, 12 or 24V, 2.5W