JH5600/5610 AC INPUT TRANSMITTERS
DIN-RAIL MOUNT, FIXED RANGE    

JH5600: AC Input Transmitter
JH5610: AC Input Transmitter with True RMS Response

Translates AC Voltages or Currents to DC Inputs from 50mV to 250Vrms, 1mA to 5 Amps RMS True-RMS Response Option Available Quick-Check Red/Green Output LEDs Unpluggable Terminal Strip AC or DC Power Options

JH5600/JH5610 PDF DATA SHEET

Model JH5600 and JH5610 AC Input Transmitters provide an isolated DC output proportional to an AC voltage or current input.

Model JH5600 is average responding, calibrated to provide accurate RMS readings with sine wave inputs. Accuracy will be degraded with nonsinusoidal waveforms such as from SCR/Triac speed and power controllers or pulse-modulated motor drives. For accurate readings with nonsinusoidal waveforms use true-RMS responding Model JH5610.

Red-green Quick-Check LEDs give a quick indication of the relative output. Red is brighter at the low end, green at high, while at mid-scale both are approximately equal. Red-only indicates offscale low while green-only indicates offscale high.

Available options include AC and DC power choices and reverse-acting transmitter (decreasing output with increasing input).

ORDERING INFORMATION

Model Number:	Specify Model JH5600 for standard (average responding) or JH5610 for true-RMS response. Add suffix A (for example, JH5600A) for AC power, D for DC power.
Input Range:	Specify any AC voltage or current range allowed by the "Input Capabilities" spec, below.
Output Range:	Specify any DC voltage or current range allowed by the "Output Capabilities" spec, below.
Power:	Specify 115Vac, 230Vac, 12Vdc or 24Vdc.
Reverse-Acting Transmitter (decreasing output with increasing input):	Change last digit of the model number to 1 (for example, JH5601A).
Loop-Powered Output:	4/20mA "current sink" output stage for connection to devices whose inputs provide 24Vdc loop excitation. Change last digit of the model number to 2 (for example, JH5602A).
Urethane Coating:	Specify Option U.

JH5600 Series transmitters snap onto 35mm DIN rail. Connections are made to the front-panel terminals. The terminal strip unplugs to facilitate calibrating or replacing the transmitter.

Connections to the 8 terminals (top to bottom) are:
    1:  AC input.
    2:  AC input.
    3:  No connection.
    4:  No connection.
    5:  Output plus.
    6:  Output minus.
    7:  Power (AC or, if DC power option, DC plus).
    8:  Power (AC or, if DC power option, DC minus).

DETAILED SPECIFICATIONS

Voltage Input Capabilities:	50mV rms minimum span, +/-250V maximum input (to 600V rms on special order). Offset ranges are allowed. (Input Impedance: 200kohms or greater.)
Current Input Capabilities:	1mA minimum span, +/-5 Amps maximum input. Offset ranges are allowed. (Input voltage drop typically 0.1V at full scale.)
Input Frequency:	40 Hz to 1kHz. For rated accuracy, Model JH5600 requires a sine wave input. Model 5610 (true RMS) remains accurate with any waveform.
Voltage Output Capabilities:	1 volt minimum output span, -10 to +15V absolute limit. Offset ranges are allowed. Maximum output load, 10mA (1Kohm at 10V output).
Current Output Capabilities:	1mA minimum output span, 0 to +25mA absolute limit. Positive offsets are allowed, negative outputs are not. Output drive capability, 24V (1,200 ohms max. at 20mA output).
Accuracy (factory calibration):	+/-0.5% of span or better.
Adjustability:	Zero and span each are adjustable approx. +/-15% of span.
Linearity:	+/-0.1% of span or better.
Response Time:	Under 200 milliseconds.
Isolation:	3-way (Power/Input/Output) 1,500Vac rms (2,100V peak).
Guaranteed Operating Temperature:	-10 to +60 deg. C (14 to 140 deg. F).
Temperature Stability:	+/-0.02% per deg. C, or better.
Power Requirements:	AC, 115 or 230Vrms, 50/60Hz, 2.5V-A. DC, 12 or 24V, 2.5W.